What are lows, mids and highs?
They're the three broad parts of everything we hear, from about 20 Hz to 20 kHz: the lows (under about 250 Hz) carry weight and the beat, the mids (250 Hz to 4 kHz) carry most of the notes, and the highs (over 4 kHz) carry air and detail, and a clear mix gives each sound its own part.
Frequency, in hertz
A sound is air moving back and forth. How many times a second it does that is its frequency, in hertz (Hz). 1 kHz is 1,000 Hz. Low numbers are low sounds: the A above middle C is 440 Hz, and the A an octave up is 880 Hz. Every octave doubles the frequency.
Human hearing runs from about 20 Hz to about 20,000 Hz (20 kHz). Where the three parts meet isn't fixed; 250 Hz and 4 kHz are a common choice, and the ones this page uses.
| Part | Range | What lives there |
|---|---|---|
| Lows | 20 Hz to 250 Hz | the thump of a kick, the body of a bass, the deepest notes you feel as much as hear |
| Mids | 250 Hz to 4 kHz | most notes of most instruments, voices, the body of chords; the range a phone plays well |
| Highs | 4 kHz to 20 kHz | hi-hats, breath, the "air" and sparkle; and hiss |
A note is more than one frequency. The lowest bass note in Lift, a song played by SynthMaker, is a D at 73.42 Hz. It also sounds quieter copies at 2, 3, 4 and more times that (146.8 Hz, 220.3 Hz, 293.7 Hz and up). These overtones give each sound its character. So a bass lives mostly in the lows, but its overtones reach into the mids, which is how you hear it on a phone (page 2).
Where Lift's parts live
Measured over the whole song, each of Lift's stems (each part as its own audio file) has its own home. The kick has 100% of its energy in the lows, and the bass 78%. The lead line has 67% in the mids, which is why you can follow it on any speaker. Even the hi-hats keep only 24% in the highs. Nothing in Lift lives mainly in the highs, which is why it sounds dark.
Two sounds in the same place fight
When two sounds share the same range, the louder one hides the quieter one. That's called masking. A muddy mix usually has too many sounds piled into roughly 200 to 500 Hz. A harsh one has too much around 2 to 5 kHz, the range our ears are most sensitive to.
So mixing is often about making room: turning one sound down in a range so another can be heard there. That's what EQ (equalisation: turning chosen ranges up or down) is for, and the next chapter is all about it.
Lift as a whole has about 64% of its energy in the lows, and only 0.13% in the presence range, 2 to 5 kHz, which makes things sound near and clear. Its remaster turned the very bottom down a little (up to 2 dB below about 60 Hz; a dB, or decibel, compares two levels, page 3) and gave a gentle 3 dB boost around 3 kHz. The presence share more than doubled, to 0.26%: still a dark mix, but a less extreme one.
Listen
1. The three parts on their own: Lows, mids, highs. 16 seconds of Lift: 4 seconds of only the lows, 4 of only the mids, 4 of only the highs, then 4 of everything. Each part is turned up so you can hear it. Listen for the highs coming and going: only some notes have anything up there.
2. Before and after the remaster:
Before: 16 seconds of Lift as first mastered;0:00 / 0:16 After: the same 16 seconds of the remaster, at the same loudness.0:00 / 0:16
Listen to the bottom of the kick and the bass, then to how near the lead sounds. The change is small, so switch a few times.
Try it in SynthMaker
Hear the three parts of one sound with a Filter.
- Make an Oscillator (wave: Saw, rich in overtones) into a Filter into a VCA into the Output. Put an Analyzer after the Filter and show its Spectrum: one line for each overtone.
- Only the lows: set the Filter's mode to Low-pass and cutoff to 250 Hz. Play a low note: what's left is round and dark. This filter falls 12 dB per octave, so the higher overtones fade rather than stop.
- Only the highs: mode High-pass, cutoff 4000 Hz: a thin fizz, the top of the same note.
- Only the mids: mode Band-pass, cutoff 1000 Hz: a nasal, telephone-like middle.
- Back on Low-pass at 250 Hz, play a low note, then a high one. The filter keeps much of the low note and almost nothing of the high one.
Where the numbers come from
- Worked out: the overtones of 73.42 Hz.
- Measured from Lift's stems and the finished song: each part's share of the lows, mids and highs, and the share from 2 to 5 kHz before and after the remaster.
- From the score and the remaster's settings: the bass's lowest note, the cut and the boost.
- Common figures, not measured here: hearing as about 20 Hz to 20 kHz (it varies, and the top falls with age); mud at about 200 to 500 Hz and harshness at about 2 to 5 kHz; and the 250 Hz and 4 kHz lines between the three parts.
- From SynthMaker's manual: the Filter falls 12 dB per octave.