SynthMaker Filament Manual Open SynthMaker (opens in a new tab)
The Low-pass gate unit's panel, 8 HP, in Tidewell's look
Tidewell

Low-pass gate: vactrol

A lamp, a light-sensitive cell and a capacitor: struck, it rings and dies away, darker and quieter at once, like wood.

Width
8 HP
Step
7 of the case
Lesson
7 · Struck wood

Open it up. Its circuit opens in SynthMaker: change a part, add one, wire it to other modules, or make it a module of your own with its own face.

Open its circuit in SynthMaker (opens in a new tab)Looking inside is free. Changing it is part of SynthMaker Pro.

Filament is being built in the open. This unit's circuit plays here in your browser, and the whole case plays in SynthMaker for Mac.

What it could be · 1 of 2

Struck wood

Rendered offline at full circuit quality. 0:45

What it could be · 2 of 2

Rain on tin

Rendered offline at full circuit quality. 0:45

Play it

2 patches with Low-pass gate in them, each played live in your browser by the same circuit solver as the app. Press Play, then turn the knobs; with Live wires on, the schematic and the parts list follow the signal.

1

Struck wood

Tutorial 7's knock: WHITE into the gate's IN, Keys' GATE into STRIKE. Each key strikes the lamp and the noise rings and dies like wood. Turn DECAY down for a woodblock.

LowPassGate · Struck wood · the parts list
circuit LowPassGate  setting decay: 47k, from 4.7k to 470k  setting offset: 100G, from 100G to 10k  setting mode: 50%  setting input: 5 V  setting output: 5 V  oversample 1x  in strike  V1 vr gnd 5V  Cs strike s 4.7u  Rs s gnd 10k  D1 s h  Ch h gnd 1u  Rd h gnd decay  U3 h f f opamp  Rf f glow 10k  Ro vr glow offset  U2 glow e a opamp  O1 a e in x slow  Rk a e 100M  Rsense e gnd 4.7k  V2 v10 gnd 10V  Pm v10 m gnd 10k mode  S1 x l m gnd at 2.5V  RL l gnd 47k  S2 c gnd gnd m at -7.5V  C1 x c 10n  U1 x out out opampend
The patch · SMPL
# SynthMaker · Filament Low-pass gate · Struck woodvoice  = Voice(mode: Mono)noise  = NoiseSource(level: 70%)lpg    = LowPassGate(decay: 33k, mode: 50%)env    = Envelope(attack: 1 ms, decay: 400 ms, sustain: 1, release: 400 ms)vca    = VCA(level: 0.9)​noise -> lpg -> vca -> outvoice.gate -> lpg.strikevoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: One way out per circuit on the web for now: WHITE is the circuit's out, PINK stays inside.

On the web: One way out per circuit on the web for now: OUT is the circuit's out, GLOW (the light's) stays inside.

2

Plucked saw

The VCO's saw, through the ladder nearly wide open, into the gate instead: every note is plucked, bright at the strike and darker as it fades. Turn DECAY past the middle to let it ring.

LowPassGate · Plucked saw · the parts list
circuit LowPassGate  setting decay: 47k, from 4.7k to 470k  setting offset: 100G, from 100G to 10k  setting mode: 50%  setting input: 5 V  setting output: 5 V  oversample 1x  in strike  V1 vr gnd 5V  Cs strike s 4.7u  Rs s gnd 10k  D1 s h  Ch h gnd 1u  Rd h gnd decay  U3 h f f opamp  Rf f glow 10k  Ro vr glow offset  U2 glow e a opamp  O1 a e in x slow  Rk a e 100M  Rsense e gnd 4.7k  V2 v10 gnd 10V  Pm v10 m gnd 10k mode  S1 x l m gnd at 2.5V  RL l gnd 47k  S2 c gnd gnd m at -7.5V  C1 x c 10n  U1 x out out opampend
The patch · SMPL
# SynthMaker · Filament Low-pass gate · Plucked sawvoice  = Voice(mode: Mono)voct   = VOct()vco    = VCO()ladder = Ladder(resonance: 0.2, cutoff: 600k, output: 1 V)lpg    = LowPassGate(decay: 100k, mode: 50%)env    = Envelope(attack: 1 ms, decay: 400 ms, sustain: 1, release: 400 ms)vca    = VCA(level: 0.45)​voice.note -> voct -> vco.voctvco -> ladder -> lpg -> vca -> outvoice.gate -> lpg.strikevoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

On the web: One way out per circuit on the web for now: OUT is the circuit's out, GLOW (the light's) stays inside.

The manual

Each rising edge at STRIKE (Keys' GATE) flashes the lamp; DECAY sets how long the glow takes to die. A held key strikes once.

As the light fades, the gate closes as a low-pass filter and a VCA together (MODE picks LP, VCA or BOTH): noise in knocks like a woodblock, a saw plucks. OFFSET holds it a little open.

Knobs

  • DECAYHow long a strike rings, about 5 ms to half a second.
  • OFFSETHolds the gate open a little, without a strike.
  • MODELP (darker), VCA (quieter) or BOTH.

Jacks

  • INinThe sound to gate.
  • STRIKEinA rising edge strikes the gate (Keys' GATE).
  • OUToutThe gated sound.

Inside: the circuit

STRIKE is AC-coupled through 4.7 µF into a hold capacitor (Ch) by a diode, so each edge charges it once and DECAY lets it go. An op-amp (U3) turns it into current for the optocoupler's lamp, and OFFSET adds a steady glow. The optocoupler's cell (O1), slow as real ones are, is the resistor of a low-pass filter with 10 nF and the top of a divider with 47k: MODE's switches choose which. U1 buffers OUT.

LowPassGate · the parts list, as the app has it
circuit LowPassGate  setting decay: 47k, from 4.7k to 470k  setting offset: 100G, from 100G to 10k  setting mode: 50%  setting input: 5 V  setting output: 5 V  oversample 1x  in strike  out glow  V1 vr gnd 5V  Cs strike s 4.7u  Rs s gnd 10k  D1 s h  Ch h gnd 1u  Rd h gnd decay  U3 h f f opamp  Rf f glow 10k  Ro vr glow offset  U2 glow e a opamp  O1 a e in x slow  Rk a e 100M  Rsense e gnd 4.7k  V2 v10 gnd 10V  Pm v10 m gnd 10k mode  S1 x l m gnd at 2.5V  RL l gnd 47k  S2 c gnd gnd m at -7.5V  C1 x c 10n  U1 x out out opampend
Op-amps and comparators 3op-amp ×3 U3, U2, U1
Diodes 1· D1
Capacitors 34.7u Cs1u Ch10n C1
Resistors 710k ×2 Rs, Rfset by DECAY Rdoffset Ro100M Rk4.7k Rsense47k RL
Pots 110k (mode) Pm
Switches 2analog switch ×2 S1, S2
Supplies 25V V110V V2

Pictures

Its lesson

Filament's makers are imaginary, except SynthMaker. Every circuit is real.