SynthMaker Filament Manual Open SynthMaker (opens in a new tab)
The Out unit's panel, 8 HP, in SynthMaker's look
SynthMaker

Out: with the OLED

Where the case meets your ears: a small screen that draws the wave coming in, a level, a release, and a row of lights from green to red.

Width
8 HP
Step
1 of the case
Lesson
1 · This synth has no oscillator

Filament is being built in the open. This unit's circuit plays here in your browser, and the whole case plays in SynthMaker for Mac.

Listen

Six circuits, one minute

Six sounds from SynthMaker's circuits (the circuits course and Filament's Ladder), rendered offline at full circuit quality: the Ladder sings, chords pour through its ten transistors, an OTA filter bubbles, a diode filter screams, an OTA bass growls, an acid filter squelches, and the Ladder sings again. The drums are SynthMaker's own. 0:58

Play it

1 patch with Out in them, each played live in your browser by the same circuit solver as the app. Press Play, then turn the knobs; with Live wires on, the schematic and the parts list follow the signal.

1

Tutorial 1's case

The whole first case: Keys into the ladder, the ladder into Out. Out's envelope and VCA start and end each note; its screen is the Scope here.

Ladder · Tutorial 1's case · the parts list
circuit Ladder  setting input: 2 V, from 0.2 V to 20 V  setting output: 2 V, from 0.2 V to 20 V  setting cutoff: 1M, from 8.2M to 82k  setting resonance: 30%  in cv: from -3 V to 2 V  V1 vcc gnd 15V  V2 gnd vneg 3V  Rb5 vcc b4 7.5k  Rb4 b4 b3 1.5k  Rb3 b3 b2 1.5k  Rb2 b2 b1 1.5k  Rb1 b1 gnd 1.5k  Rin in bl 47k  Nl bl gnd thermal 1k  Nr br gnd thermal 1k  Rfb fbk br 9.1k  P1 out fbk gnd 1k resonance  Q1 l1 bl tail 2N3904  Q2 r1 br tail 2N3904  C1 l1 r1 68n  Q3 l2 b1 l1 2N3904  Q4 r2 b1 r1 2N3904  C2 l2 r2 68n  Q5 l3 b2 l2 2N3904  Q6 r3 b2 r2 2N3904  C3 l3 r3 68n  Q7 l4 b3 l3 2N3904  Q8 r4 b3 r3 2N3904  C4 l4 r4 68n  Q9 vcc b4 l4 2N3904  Q10 vcc b4 r4 2N3904  U1 l4 bufl bufl opamp  U2 r4 bufr bufr opamp  R1 bufl m 10k  R2 m out 500k  R3 bufr p 10k  R4 p gnd 500k  U3 p m out opamp  Rref vcc nref cutoff  Q11 nref vneg nexp 2N3904  U4 vneg nref nexp opamp rails 15V  Q12 tail ncv nexp 2N3904  Rcv cv ncv 100k  Rcg ncv vneg 1.82kend
The patch · SMPL
# SynthMaker · Filament Out · Tutorial 1's casevoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)ladder = Ladder(resonance: 0.88, cutoff: 1.49M, output: 1 V)env    = Envelope(attack: 25 ms, decay: 400 ms, sustain: 0.8, release: 350 ms)vca    = VCA(level: 0.75)​voice.note -> voct -> trim -> ladder.cvladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

The manual

Whatever is plugged into IN is what you hear. The OLED screen draws its wave as it plays, so you can see a filter starting to ring before you hear it sing.

Out also holds the case's final amplifier: it opens with each note and closes over RELEASE when the key is let go, so a patch with nothing to shape its notes still starts and stops cleanly. LEVEL sets how loud, and the six lights show it, green, then amber, then red.

Knobs

  • LEVELHow loud the case plays.
  • RELEASEHow long a note takes to fade after the key is let go, 10 ms to 4 s.

Jacks

  • INinThe sound to hear: the end of every patch.

Inside: the circuit

Out is SynthMaker's own glue, made of the app's built-in modules rather than a circuit: an Analyzer for the screen, an Envelope and a VCA for the notes' start and end, and the level lights reading the VCA's output.

Pictures

Follow along

Filament's makers are imaginary, except SynthMaker. Every circuit is real.