SynthMaker Filament Manual Open SynthMaker (opens in a new tab)
The VCO unit's panel, 10 HP, in Rookery Electric's look
Rookery Electric

VCO: sawtooth core

A sawtooth core: a capacitor charged by an exponential current and snapped back by a comparator, bright enough to cut through anything, with a pulse whose width you can turn.

Width
10 HP
Step
2 of the case
Lesson
2 · Give it an oscillator

Open it up. Its circuit opens in SynthMaker: change a part, add one, wire it to other modules, or make it a module of your own with its own face.

Open its circuit in SynthMaker (opens in a new tab)Looking inside is free. Changing it is part of SynthMaker Pro.

Filament is being built in the open. This unit's circuit plays here in your browser, and the whole case plays in SynthMaker for Mac.

What it could be · 1 of 2

Saws opening

Rendered offline at full circuit quality. The hats are the course's noise circuit. 0:45

What it could be · 2 of 2

Pulse width

Rendered offline at full circuit quality. The kick is the Ladder too, pinged by a short pulse; the hats and snare are the course's noise circuits. 0:45

Play it

3 patches with VCO in them, each played live in your browser by the same circuit solver as the app. Press Play, then turn the knobs; with Live wires on, the schematic and the parts list follow the signal.

1

Saw through the ladder

Tutorial 2's patch: Keys' V/OCT into the VCO and the ladder, the VCO's SAW into the ladder's IN, the cutoff two octaves above the note and the resonance at 60%.

VCO · Saw through the ladder · the parts list
circuit VCO  setting tune: 50%  setting output: 5 V  oversample 4x  in voct  V1 vcc gnd 15V  V2 gnd vee 15V  V3 vh gnd 8.375V  V4 v5 gnd 5V  Rref vcc nref 1.2738M  Q1 nref gnd nexp 2N3904  U1 gnd nref nexp opamp rails 15V  Q2 sum ncv nexp 2N3904  Rv voct ncv 1k  Rt tn ncv 33k  Rg ncv gnd 18.265  P1 vcc tn vee 100k tune  C1 ramp sum 10n  U2 gnd sum ramp opamp  S1 ramp sum gnd q on 10 off 10G at 5V  U3 ref ramp q comparator rails -10V 0.5V  Ra ref q 40k  Rb vh ref 30k  U4 ramp m out opamp  Rf out m 12.22k  Rs m v5 10k  Rin in gnd 1Mend
The patch · SMPL
# SynthMaker · Filament VCO · Saw through the laddervoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)vco    = VCO()ladder = Ladder(resonance: 0.6, cutoff: 372k, output: 1 V)env    = Envelope(attack: 25 ms, decay: 400 ms, sustain: 0.8, release: 350 ms)vca    = VCA(level: 0.5)​voice.note -> voct -> vco.voctvoct -> trim -> ladder.cvvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

2

Pulse, its width moving

The PULSE output on its own, a slow LFO turning WIDTH: the hollow square thins to a nasal buzz and back. Turn WIDTH to set where it moves around.

VCOPulse · Pulse, its width moving · the parts list
circuit VCOPulse  setting tune: 50%  setting width: 50%, from 5% to 95%  setting output: 5 V  oversample 4x  in voct  V1 vcc gnd 15V  V2 gnd vee 15V  V3 vh gnd 8.375V  V4 v5 gnd 5V  Rref vcc nref 1.2738M  Q1 nref gnd nexp 2N3904  U1 gnd nref nexp opamp rails 15V  Q2 sum ncv nexp 2N3904  Rv voct ncv 1k  Rt tn ncv 33k  Rg ncv gnd 18.265  P1 vcc tn vee 100k tune  C1 ramp sum 10n  U2 gnd sum ramp opamp  S1 ramp sum gnd q on 10 off 10G at 5V  U3 ref ramp q comparator rails -10V 0.5V  Ra ref q 40k  Rb vh ref 30k  U4 ramp m saw opamp  Rf saw m 12.22k  Rs m v5 10k  P2 v5 pw lo 10k width  Rl lo gnd 1.111k  U5 pw ramp out comparator rails -5V 5V  Rin in gnd 1Mend
The patch · SMPL
# SynthMaker · Filament VCO · Pulse, its width movingvoice  = Voice(mode: Mono)voct   = VOct()vco    = VCOPulse()lfo    = LFO(shape: Triangle, rate: 0.25 Hz, depth: 0.8, retrigger: Free)env    = Envelope(attack: 15 ms, decay: 400 ms, sustain: 0.85, release: 400 ms)vca    = VCA(level: 0.12)​voice.note -> voct -> vco.voctlfo -> vco.widthvco -> vca -> outvoice.gate -> env -> vca.gain
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: A copy of the VCO whose out is PULSE (SAW's op-amp drives a node of its own), until the web plays several outputs per circuit; in rests on 1 MΩ to ground.

3

Saw, the ladder wide open

SAW into the ladder with CUTOFF all the way up and no resonance: nearly every harmonic of the sawtooth, the bright edge every filter in the case gets to shape. Turn CUTOFF down to hear them go.

VCO · Saw, the ladder wide open · the parts list
circuit VCO  setting tune: 50%  setting output: 5 V  oversample 4x  in voct  V1 vcc gnd 15V  V2 gnd vee 15V  V3 vh gnd 8.375V  V4 v5 gnd 5V  Rref vcc nref 1.2738M  Q1 nref gnd nexp 2N3904  U1 gnd nref nexp opamp rails 15V  Q2 sum ncv nexp 2N3904  Rv voct ncv 1k  Rt tn ncv 33k  Rg ncv gnd 18.265  P1 vcc tn vee 100k tune  C1 ramp sum 10n  U2 gnd sum ramp opamp  S1 ramp sum gnd q on 10 off 10G at 5V  U3 ref ramp q comparator rails -10V 0.5V  Ra ref q 40k  Rb vh ref 30k  U4 ramp m out opamp  Rf out m 12.22k  Rs m v5 10k  Rin in gnd 1Mend
The patch · SMPL
# SynthMaker · Filament VCO · Saw, the ladder wide openvoice  = Voice(mode: Mono)voct   = VOct()vco    = VCO()ladder = Ladder(resonance: 0.05, cutoff: 82k, input: 1 V, output: 1.2 V)env    = Envelope(attack: 15 ms, decay: 400 ms, sustain: 0.8, release: 300 ms)vca    = VCA(level: 0.4)​voice.note -> voct -> vco.voctvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

The manual

Plug Keys' V/OCT into V/OCT and the VCO plays the notes, within a cent of each one from C1 to C5. SAW is the bright, buzzy wave every subtractive patch starts from; PULSE is a square wave whose WIDTH moves from a thin, nasal 5% to a hollow 50% and back to 95%.

TUNE moves the pitch about five and a half semitones each way, to tune the VCO against another or detune it on purpose. FINE does the same by voltage in a much smaller range, about 20 cents at 5 V: a slow wave there makes two VCOs beat slower and faster.

Knobs

  • TUNEThe pitch, about 5½ semitones each way around the note.
  • WIDTHThe pulse's width, from 5% to 95% of each cycle: 50% is a square wave.

Jacks

  • FINEinFine tune by voltage: about 20 cents at 5 V, either way (±5 V, ±20 cents).
  • V/OCTinThe pitch, 1 V per octave, C4 at 0 V.
  • SAWoutThe sawtooth, 10 V peak to peak.
  • PULSEoutThe pulse wave, ±5 V, its width set by WIDTH.

Inside: the circuit

V/OCT goes through a divider into an exponential converter: Q1 holds a reference current and Q2 multiplies it by e for every 26 mV at its base, so each volt at V/OCT doubles the current, an octave up. That current charges C1 through the integrator U2, so the ramp rises at a speed set by the note. When it reaches 5 V, the comparator U3 closes the switch S1 across C1 and lets it go again at 0.5 V: the ramp snaps back, and the cycle repeats. U4 doubles and centres the ramp for SAW; U5 compares it with WIDTH's voltage for PULSE. It runs at 4× oversampling, so the resets land exactly within a sample and their aliases stay high and quiet. FINE is its own small circuit beside it, a 300k over 1k divider into V/OCT, so it can't load the exponential converter and move the tuning.

VCO · the parts list, as the app has it
circuit VCO  setting tune: 50%  setting width: 50%, from 5% to 95%  setting output: 5 V  oversample 4x  in voct  out pulse  V1 vcc gnd 15V  V2 gnd vee 15V  V3 vh gnd 8.375V  V4 v5 gnd 5V  Rref vcc nref 1.2738M  Q1 nref gnd nexp 2N3904  U1 gnd nref nexp opamp rails 15V  Q2 sum ncv nexp 2N3904  Rv voct ncv 1k  Rt tn ncv 33k  Rg ncv gnd 18.265  P1 vcc tn vee 100k tune  C1 ramp sum 10n  U2 gnd sum ramp opamp  S1 ramp sum gnd q on 10 off 10G at 5V  U3 ref ramp q comparator rails -10V 0.5V  Ra ref q 40k  Rb vh ref 30k  U4 ramp m out opamp  Rf out m 12.22k  Rs m v5 10k  P2 v5 pw lo 10k width  Rl lo gnd 1.111k  U5 pw ramp pulse comparator rails -5V 5Vend
Transistors 22N3904 ×2 Q1, Q2
Op-amps and comparators 5op-amp ×3 U1, U2, U4comparator ×2 U3, U5
Capacitors 110n C1
Resistors 91.2738M Rref1k Rv33k Rt18.265 Rg40k Ra30k Rb12.22k Rf10k Rs1.111k Rl
Pots 2100k (tune) P110k (width) P2
Switches 1analog switch S1
Supplies 415V ×2 V1, V28.375V V35V V4
FineTune · the parts list, as the app has it
circuit FineTune  setting input: 5 V  setting output: 5 V  oversample 1x  R1 in out 300k  R2 out gnd 1kend
Resistors 2300k R11k R2

Pictures

Follow along

Filament's makers are imaginary, except SynthMaker. Every circuit is real.