
Noise: white and pink
Noise from a real avalanche junction: white for hats and hiss, pink for breath and wind.
- Width
- 4 HP
- Step
- 6 of the case
- Lesson
- 6 · Wind, breath and hats
Open it up. Its circuit opens in SynthMaker: change a part, add one, wire it to other modules, or make it a module of your own with its own face.
Open its circuit in SynthMaker (opens in a new tab)Looking inside is free. Changing it is part of SynthMaker Pro.Filament is being built in the open. This unit's circuit plays here in your browser, and the whole case plays in SynthMaker for Mac.
What it could be · 1 of 2
Wind and surf
Rendered offline at full circuit quality. 0:45
What it could be · 2 of 2
Breath and hats
Rendered offline at full circuit quality. The kick is the Ladder too, pinged by a short pulse; a plain sine thumps under the snare. 0:43
Play it
2 patches with Noise in them, each played live in your browser by the same circuit solver as the app. Press Play, then turn the knobs; with Live wires on, the schematic and the parts list follow the signal.
Hi-hats
Tutorial 6's hats: WHITE into the VCA, a short envelope in its CV, struck on every eighth. Turn DECAY up for an open hat.
circuit NoiseSource setting level: 70% setting output: 5 V Rin in gnd 100k N1 j gnd avalanche Rb j gnd 100k C1 j b 100n R1 b gnd 100k U1 b m w opamp Rg m g 1k Cg g gnd 10u Rf w m 470k P1 w lv gnd 10k level U2 lv out out opamp R6 out k 10k R7 k gnd 2.7M R2 k k2 6.8k C2 k2 gnd 330n R3 k k3 2.7k C3 k3 gnd 120n R4 k k4 1.2k C4 k4 gnd 47n R5 k k5 270 C5 k5 gnd 33n U3 k m3 pink opamp Rf3 pink m3 82k Rg3 m3 gnd 10kend# SynthMaker · Filament Noise · Hi-hatsvoice = Voice(mode: Mono)noise = NoiseSource(level: 70%)adsr = ADSR(attack: 1k, decay: 39k, sustain: 0%, release: 30k)ota = OTAVCA(level: 0%)env = Envelope(attack: 1 ms, decay: 400 ms, sustain: 1, release: 80 ms)vca = VCA(level: 0.7)noise -> ota -> vca -> outvoice.gate -> adsr.gateadsr -> ota.cvvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2Press Play to see the wave after the circuit, at out.
On the web: One way out per circuit on the web for now: WHITE is the circuit's out, PINK stays inside.
On the web: Every web circuit has an in (the app's envelope needs none): here it rests on 1 MΩ to ground, joined to nothing else.
On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet): here OUT is the circuit's out and GAIN, the light's, stays inside.
Breath
PINK through the VCA, the envelope slow: each held note breathes in and out. Pink is darker than white, 3 dB down every octave.
circuit NoiseSourcePink setting level: 70% setting output: 5 V Rin in gnd 100k N1 j gnd avalanche Rb j gnd 100k C1 j b 100n R1 b gnd 100k U1 b m w opamp Rg m g 1k Cg g gnd 10u Rf w m 470k P1 w lv gnd 10k level U2 lv wb wb opamp R6 wb k 10k R7 k gnd 2.7M R2 k k2 6.8k C2 k2 gnd 330n R3 k k3 2.7k C3 k3 gnd 120n R4 k k4 1.2k C4 k4 gnd 47n R5 k k5 270 C5 k5 gnd 33n U3 k m3 out opamp Rf3 out m3 82k Rg3 m3 gnd 10kend# SynthMaker · Filament Noise · Breathvoice = Voice(mode: Mono)noise = NoiseSourcePink(level: 70%)adsr = ADSR(attack: 470k, decay: 470k, sustain: 80%, release: 680k)ota = OTAVCA(level: 0%)env = Envelope(attack: 5 ms, decay: 400 ms, sustain: 1, release: 1500 ms)vca = VCA(level: 0.8)noise -> ota -> vca -> outvoice.gate -> adsr.gateadsr -> ota.cvvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2Press Play to see the wave after the circuit, at out.
On the web: A copy of the noise whose out is PINK (WHITE's buffer drives a node of its own), until the web plays several outputs per circuit.
On the web: Every web circuit has an in (the app's envelope needs none): here it rests on 1 MΩ to ground, joined to nothing else.
On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet): here OUT is the circuit's out and GAIN, the light's, stays inside.
The manual
WHITE has the same energy at every frequency: bright hiss. PINK is the same noise through a filter that takes 3 dB off every octave: darker, like wind or breath. LEVEL sets both, and CV turns LEVEL from where it's set: an LFO there makes the noise breathe.
Through a short envelope and the VCA it's a hi-hat; through the ladder, resonance up, it's breath and wind.
Knobs
- LEVELHow loud, for both outputs.
Jacks
- CVinTurns LEVEL from where it's set: 5 V is half its travel.
- WHITEoutWhite noise.
- PINKoutPink noise, 3 dB down every octave.
Inside: the circuit
A small transistor's junction, reverse-biased into avalanche (N1), crackles with random current. C1 passes it to an op-amp with a gain of 471 (U1), LEVEL's pot and a buffer (U2) make WHITE, and a ladder of four RC pairs (R2 to R5, C2 to C5) under 2.7M takes off 3 dB an octave before U3 lifts it again as PINK. CV is wired to LEVEL's own pot, so it turns it as a hand would.
circuit NoiseSource setting level: 70% setting output: 5 V out pink Rin in gnd 100k N1 j gnd avalanche Rb j gnd 100k C1 j b 100n R1 b gnd 100k U1 b m w opamp Rg m g 1k Cg g gnd 10u Rf w m 470k P1 w lv gnd 10k level U2 lv out out opamp R6 out k 10k R7 k gnd 2.7M R2 k k2 6.8k C2 k2 gnd 330n R3 k k3 2.7k C3 k3 gnd 120n R4 k k4 1.2k C4 k4 gnd 47n R5 k k5 270 C5 k5 gnd 33n U3 k m3 pink opamp Rf3 pink m3 82k Rg3 m3 gnd 10kend| Op-amps and comparators 3 | op-amp ×3 U1, U2, U3 |
|---|---|
| Capacitors 6 | 100n C110u Cg330n C2120n C347n C433n C5 |
| Resistors 13 | 100k ×3 Rin, Rb, R11k Rg470k Rf10k ×2 R6, Rg32.7M R76.8k R22.7k R31.2k R4270 R582k Rf3 |
| Pots 1 | 10k (level) P1 |
Pictures


Follow along
Filament 6
Wind, breath and hats
Add Ondine Labs' noise: pink through the resonant ladder for breath and wind, white into the VCA with a short envelope for hi-hats.
This lesson is in SynthMaker for Mac: Help › Lessons › Filament 6.
Build it in SynthMaker for MacFilament's makers are imaginary, except SynthMaker. Every circuit is real.