SynthMaker Filament Manual Open SynthMaker (opens in a new tab)
The LFO unit's panel, 6 HP, in Ondine Labs's look
Ondine Labs

LFO: triangle core

A slow oscillator from a real triangle core: sweeps, breathing and wobble, from one twentieth of a hertz to thirty.

Width
6 HP
Step
4 of the case
Lesson
4 · Make it breathe

Open it up. Its circuit opens in SynthMaker: change a part, add one, wire it to other modules, or make it a module of your own with its own face.

Open its circuit in SynthMaker (opens in a new tab)Looking inside is free. Changing it is part of SynthMaker Pro.

Filament is being built in the open. This unit's circuit plays here in your browser, and the whole case plays in SynthMaker for Mac.

What it could be · 1 of 2

Slow tide

Rendered offline at full circuit quality. 0:45

What it could be · 2 of 2

Wobble and trill

Rendered offline at full circuit quality. The kick is the Ladder too, pinged by a short pulse; the hats and snare are the noise unit through the VCA. 0:42

Play it

3 patches with LFO in them, each played live in your browser by the same circuit solver as the app. Press Play, then turn the knobs; with Live wires on, the schematic and the parts list follow the signal.

1

Breathe

Tutorial 4's patch: the LFO's TRI in the ladder's CV where the envelope's cable was, RATE at 0.3 Hz. Long notes open and close slowly, as if breathing. Turn RATE up and the breath quickens.

TriangleCore · Breathe · the parts list
circuit TriangleCore  setting rate: 250k, from 8.333k to 5M  setting output: 5 V  oversample 1x  U1 h gnd sq comparator rails -5V 5V  R1 ramp h 100k  R2 sq h 100k  Rr sq n rate  C1 ramp n 1u  U2 gnd n ramp opamp  Ri ramp m 100k  Rf m out 100k  U3 gnd m out opamp  Ro sq square 1k  Co square gnd 22n  Rin in gnd 100kend
The patch · SMPL
# SynthMaker · Filament LFO · Breathevoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)vco    = VCO()lfo    = TriangleCore(rate: 833k)atten  = Attenuverter(amount: 70%)ladder = Ladder(resonance: 0.6, cutoff: 1.2M, output: 1 V)env    = Envelope(attack: 60 ms, decay: 400 ms, sustain: 0.9, release: 600 ms)vca    = VCA(level: 0.5)​voice.note -> voct -> vco.voctvoct -> trim -> ladder.cvlfo -> atten -> ladder.cvvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet): here TRI is the circuit's out and SQUARE stays inside.

2

Wobble

RATE up to 6 Hz and the resonance higher: low notes wobble as the cutoff swings six times a second. Turn RATE to set the wobble's speed.

TriangleCore · Wobble · the parts list
circuit TriangleCore  setting rate: 250k, from 8.333k to 5M  setting output: 5 V  oversample 1x  U1 h gnd sq comparator rails -5V 5V  R1 ramp h 100k  R2 sq h 100k  Rr sq n rate  C1 ramp n 1u  U2 gnd n ramp opamp  Ri ramp m 100k  Rf m out 100k  U3 gnd m out opamp  Ro sq square 1k  Co square gnd 22n  Rin in gnd 100kend
The patch · SMPL
# SynthMaker · Filament LFO · Wobblevoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)vco    = VCO()lfo    = TriangleCore(rate: 41.7k)atten  = Attenuverter(amount: 85%)ladder = Ladder(resonance: 0.7, cutoff: 2.2M, input: 4 V, output: 2 V)env    = Envelope(attack: 2 ms, decay: 300 ms, sustain: 0.85, release: 120 ms)vca    = VCA(level: 0.5)​voice.note -> voct -> vco.voctvoct -> trim -> ladder.cvlfo -> atten -> ladder.cvvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet): here TRI is the circuit's out and SQUARE stays inside.

3

Square trill

SQUARE instead of TRI, at 2.3 Hz: the cutoff jumps between two places instead of sweeping, and the resonance trills. Turn CUTOFF to move both.

TriangleCoreSquare · Square trill · the parts list
circuit TriangleCoreSquare  setting rate: 250k, from 8.333k to 5M  setting output: 5 V  oversample 1x  U1 h gnd sq comparator rails -5V 5V  R1 ramp h 100k  R2 sq h 100k  Rr sq n rate  C1 ramp n 1u  U2 gnd n ramp opamp  Ri ramp m 100k  Rf m tri 100k  U3 gnd m tri opamp  Ro sq out 1k  Co out gnd 22n  Rin in gnd 100kend
The patch · SMPL
# SynthMaker · Filament LFO · Square trillvoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)vco    = VCO()lfo    = TriangleCoreSquare(rate: 109k)atten  = Attenuverter(amount: 55%)ladder = Ladder(resonance: 0.65, cutoff: 1.5M, output: 1 V)env    = Envelope(attack: 30 ms, decay: 400 ms, sustain: 0.9, release: 500 ms)vca    = VCA(level: 0.5)​voice.note -> voct -> vco.voctvoct -> trim -> ladder.cvlfo -> atten -> ladder.cvvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

On the web: A copy of the LFO whose out is SQUARE (TRI's op-amp drives a node of its own), until the web plays several outputs per circuit.

The manual

TRI is a triangle wave, ±5 V, that rises and falls forever, whatever the keys are doing. Into the ladder's CV jack it opens and closes the filter: slowly, the notes breathe; fast, they wobble.

SQUARE flips between +5 V and −5 V at the same rate, high while TRI rises: into the ladder's CV it jumps the cutoff between two places, a trill rather than a sweep. The light breathes with TRI.

Knobs

  • RATEHow fast it moves, 0.05 Hz (one sweep every 20 s) to 30 Hz, about 1 Hz at noon; the scale is printed in hertz.

Jacks

  • TRIoutThe triangle, ±5 V.
  • SQUAREoutThe square, ±5 V, high while TRI rises.

Inside: the circuit

Two op-amps and a comparator chase each other. U2 integrates: with SQUARE high, C1 charges steadily through RATE and the ramp falls in a straight line; U1, a comparator with positive feedback through two 100k resistors, flips when the ramp reaches −5 V, and the ramp turns round and climbs. So the ramp runs between ±5 V at 1/(4 × RATE × C1): 1 Hz at 250k. U3 inverts it as TRI, and SQUARE leaves through 1k and 22 nF, which keep its edges clean.

TriangleCore · the parts list, as the app has it
circuit TriangleCore  setting rate: 250k, from 8.333k to 5M  setting output: 5 V  oversample 1x  out square  U1 h gnd sq comparator rails -5V 5V  R1 ramp h 100k  R2 sq h 100k  Rr sq n rate  C1 ramp n 1u  U2 gnd n ramp opamp  Ri ramp m 100k  Rf m out 100k  U3 gnd m out opamp  Ro sq square 1k  Co square gnd 22n  Rin in gnd 100kend
Op-amps and comparators 3comparator U1op-amp ×2 U2, U3
Capacitors 21u C122n Co
Resistors 7100k ×5 R1, R2, Ri, Rf, Rinrate Rr1k Ro

Pictures

Follow along

Filament's makers are imaginary, except SynthMaker. Every circuit is real.