SynthMaker Filament Manual Open SynthMaker (opens in a new tab)
The Envelope unit's panel, 8 HP, in Ondine Labs's look
Ondine Labs

Envelope: ADSR

An ADSR built from comparators, diodes and one capacitor: attack, decay, sustain and release, so every note gets a shape.

Width
8 HP
Step
3 of the case
Lesson
3 · Give each note a shape

Open it up. Its circuit opens in SynthMaker: change a part, add one, wire it to other modules, or make it a module of your own with its own face.

Open its circuit in SynthMaker (opens in a new tab)Looking inside is free. Changing it is part of SynthMaker Pro.

Filament is being built in the open. This unit's circuit plays here in your browser, and the whole case plays in SynthMaker for Mac.

What it could be · 1 of 2

Pluck and swell

Rendered offline at full circuit quality. The hats are the course's noise circuit. 0:45

What it could be · 2 of 2

Gate dance

Rendered offline at full circuit quality. The kick is the Ladder too, pinged by a short pulse; the hats and snare are the course's noise circuits. 0:43

Play it

3 patches with Envelope in them, each played live in your browser by the same circuit solver as the app. Press Play, then turn the knobs; with Live wires on, the schematic and the parts list follow the signal.

1

Pluck

Tutorial 3's patch: Keys' GATE into the envelope, ENV into the ladder's CV with the CV knob at 8. A fast attack, a short decay and a low sustain: every note plucks.

ADSR · Pluck · the parts list
circuit ADSR  setting attack: 10k, from 1k to 1M  setting decay: 100k, from 1k to 1M  setting sustain: 50%  setting release: 100k, from 1k to 1M  setting output: 10 V  in gate  V1 vcc gnd 15V  V2 gnd vee 15V  Rt1 vcc th 140k  Rt2 th gnd 10k  U1 gate th g comparator rails 0V 10V  U3 p env t comparator rails 0V 15V  Cp g p 1n  Rp p gnd 100k  Rb p vee 10M  Rf t p 50k  D1 t ka 1N4148  Ra ka env attack  S1 env kd g t at 5V  Rd kd sus decay  P1 g sus gnd 10k sustain  Rr env kr release  D2 kr g 1N4148  C1 env gnd 1u  U2 env out out opamp  Rin in gnd 1Mend
The patch · SMPL
# SynthMaker · Filament Envelope · Pluckvoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)vco    = VCO()adsr   = ADSR(attack: 1k, decay: 150k, sustain: 15%, release: 100k)atten  = Attenuverter(amount: 80%)ladder = Ladder(resonance: 0.6, cutoff: 1.49M, output: 1 V)env    = Envelope(attack: 5 ms, decay: 400 ms, sustain: 0.8, release: 350 ms)vca    = VCA(level: 0.5)​voice.note -> voct -> vco.voctvoct -> trim -> ladder.cvvoice.gate -> adsr.gateadsr -> atten -> ladder.cvvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

On the web: Every web circuit has an in (the app's envelope needs none): here it rests on 1 MΩ to ground, joined to nothing else.

2

Swell

The same patch, the envelope slow: a long attack and a high sustain open the filter gradually through each held note, and a long release closes it after.

ADSR · Swell · the parts list
circuit ADSR  setting attack: 10k, from 1k to 1M  setting decay: 100k, from 1k to 1M  setting sustain: 50%  setting release: 100k, from 1k to 1M  setting output: 10 V  in gate  V1 vcc gnd 15V  V2 gnd vee 15V  Rt1 vcc th 140k  Rt2 th gnd 10k  U1 gate th g comparator rails 0V 10V  U3 p env t comparator rails 0V 15V  Cp g p 1n  Rp p gnd 100k  Rb p vee 10M  Rf t p 50k  D1 t ka 1N4148  Ra ka env attack  S1 env kd g t at 5V  Rd kd sus decay  P1 g sus gnd 10k sustain  Rr env kr release  D2 kr g 1N4148  C1 env gnd 1u  U2 env out out opamp  Rin in gnd 1Mend
The patch · SMPL
# SynthMaker · Filament Envelope · Swellvoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)vco    = VCO()adsr   = ADSR(attack: 680k, decay: 470k, sustain: 70%, release: 560k)atten  = Attenuverter(amount: 85%)ladder = Ladder(resonance: 0.55, cutoff: 2.2M, output: 1 V)env    = Envelope(attack: 60 ms, decay: 400 ms, sustain: 0.9, release: 700 ms)vca    = VCA(level: 0.5)​voice.note -> voct -> vco.voctvoct -> trim -> ladder.cvvoice.gate -> adsr.gateadsr -> atten -> ladder.cvvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

On the web: Every web circuit has an in (the app's envelope needs none): here it rests on 1 MΩ to ground, joined to nothing else.

3

Acid squelch

Low notes, the resonance high and a snappy decay: the envelope throws the cutoff up on every note and the ladder squelches as it falls.

ADSR · Acid squelch · the parts list
circuit ADSR  setting attack: 10k, from 1k to 1M  setting decay: 100k, from 1k to 1M  setting sustain: 50%  setting release: 100k, from 1k to 1M  setting output: 10 V  in gate  V1 vcc gnd 15V  V2 gnd vee 15V  Rt1 vcc th 140k  Rt2 th gnd 10k  U1 gate th g comparator rails 0V 10V  U3 p env t comparator rails 0V 15V  Cp g p 1n  Rp p gnd 100k  Rb p vee 10M  Rf t p 50k  D1 t ka 1N4148  Ra ka env attack  S1 env kd g t at 5V  Rd kd sus decay  P1 g sus gnd 10k sustain  Rr env kr release  D2 kr g 1N4148  C1 env gnd 1u  U2 env out out opamp  Rin in gnd 1Mend
The patch · SMPL
# SynthMaker · Filament Envelope · Acid squelchvoice  = Voice(mode: Mono)voct   = VOct()trim   = VTrim(scale: 1.0125)vco    = VCO()adsr   = ADSR(attack: 1k, decay: 120k, sustain: 5%, release: 60k)atten  = Attenuverter(amount: 92%)ladder = Ladder(resonance: 0.74, cutoff: 3.9M, input: 4 V, output: 2 V)env    = Envelope(attack: 2 ms, decay: 300 ms, sustain: 0.8, release: 80 ms)vca    = VCA(level: 0.55)​voice.note -> voct -> vco.voctvoct -> trim -> ladder.cvvoice.gate -> adsr.gateadsr -> atten -> ladder.cvvco -> ladder -> vca -> outvoice.gate -> env -> vca.gainvoice.velocity -> vca.gain2
Scope · out

Press Play to see the wave after the circuit, at out.

A short riff through the circuit, round and round. Turn the knobs while it plays. Open in SynthMaker ↗ (opens in a new tab)

On the web: The web engine plays one way out per circuit for now (the app's several outputs per circuit aren't on the web yet), and every web circuit has an in: here SAW is the circuit's out, PULSE's parts are left out, and in rests on 1 MΩ to ground.

On the web: Every web circuit has an in (the app's envelope needs none): here it rests on 1 MΩ to ground, joined to nothing else.

The manual

When GATE goes high, ENV rises over ATTACK to its top, falls over DECAY to the SUSTAIN level, and stays there while the key is held. Let go, and it falls to zero over RELEASE.

Into the ladder's CV jack, it opens the filter at the start of every note and closes it again: short attack and decay with a low sustain is a pluck, the classic squelch with resonance up; a long attack with high sustain is a swell. It makes no sound itself; it moves something that does.

Knobs

  • ATTACKHow long the rise takes, 1 ms to 1 s.
  • DECAYHow long it takes to fall to the sustain level, 1 ms to 1 s.
  • SUSTAINThe level held while the key stays down, from none to full.
  • RELEASEHow long it takes to fall to zero after the key is let go, 1 ms to 1 s.

Jacks

  • GATEinStarts the envelope when it goes high (Keys' GATE), and releases it when it drops.
  • ENVoutThe envelope, 0 to 10 V.

Inside: the circuit

U1 squares up the gate against a 1 V threshold. Its rising edge kicks U3 through Cp, so U3's output goes high and charges C1 through D1 and the ATTACK resistor towards 15 V. At 10 V U3 switches off and stays off until the next gate's edge; the switch S1, closed while the gate is high and U3 is off, lets C1 fall through DECAY towards SUSTAIN's share of the gate. When the gate ends, C1 drains through D2 and RELEASE. U2 buffers the capacitor's voltage as ENV.

ADSR · the parts list, as the app has it
circuit ADSR  setting attack: 10k, from 1k to 1M  setting decay: 100k, from 1k to 1M  setting sustain: 50%  setting release: 100k, from 1k to 1M  setting output: 10 V  in gate  V1 vcc gnd 15V  V2 gnd vee 15V  Rt1 vcc th 140k  Rt2 th gnd 10k  U1 gate th g comparator rails 0V 10V  U3 p env t comparator rails 0V 15V  Cp g p 1n  Rp p gnd 100k  Rb p vee 10M  Rf t p 50k  D1 t ka 1N4148  Ra ka env attack  S1 env kd g t at 5V  Rd kd sus decay  P1 g sus gnd 10k sustain  Rr env kr release  D2 kr g 1N4148  C1 env gnd 1u  U2 env out out opampend
Op-amps and comparators 3comparator ×2 U1, U3op-amp U2
Diodes 21N4148 ×2 D1, D2
Capacitors 21n Cp1u C1
Resistors 8140k Rt110k Rt2100k Rp10M Rb50k Rfset by ATTACK Raset by DECAY Rdset by RELEASE Rr
Pots 110k (sustain) P1
Switches 1analog switch S1
Supplies 215V ×2 V1, V2

Pictures

Follow along

Filament's makers are imaginary, except SynthMaker. Every circuit is real.